Aero-ZnS prepared by physical vapor transport on three-dimensional networks of sacrificial ZnO microtetrapods

• Veaceslav Ursaki,
• Tudor Braniste,
• Victor Zalamai,
• Emil Rusu,
• Vladimir Ciobanu,
• Vadim Morari,
• Daniel Podgornii,
• Pier Carlo Ricci,
• Rainer Adelung and
• Ion Tiginyanu

Beilstein J. Nanotechnol. 2024, 15, 490–499, doi:10.3762/bjnano.15.44

• processes, including those related to oxygen species adsorbed by the huge surface of the aeromaterial, as previously observed in ZnS nanostructures [42]. Some of these states may be related to oxygen vacancies and complex centers. Under ambient conditions, some oxygen species from the air are adsorbed at

• the surface states, forming complexes with oxygen vacancies. These complexes may be responsible for the PL band around 2.4 eV. Under vacuum conditions, the oxygen species are desorbed from the surface, annihilating the formed complexes. As a result, the intensity of the PL band around 2.4 eV decreases

• [43]. The adsorption of oxygen species from the environment on the sample surface promoted by oxygen vacancies results also in a strong interaction between the photoexcited electrons captured by oxygen vacancies and the adsorbed oxygen species. The formation of the SnO2 phase in the prepared aero-ZnS

Classification and application of metal-based nanoantioxidants in medicine and healthcare

• Nguyen Nhat Nam,
• Nguyen Khoi Song Tran,
• Tan Tai Nguyen,
• Nguyen Ngoc Trai,
• Nguyen Phuong Thuy,
• Hoang Dang Khoa Do,
• Nhu Hoa Thi Tran and
• Kieu The Loan Trinh

Beilstein J. Nanotechnol. 2024, 15, 396–415, doi:10.3762/bjnano.15.36

• ]. The heterostructures increase surface electron deficiency, redox couples, and oxygen vacancies through an intrinsic electric field and lattice mismatch at the metal–semiconductor interface. Thus, a high level of oxygen vacancies enhances the adsorption and activation of oxygen-containing ROS, that is

• higher Ce4+ content are known to have higher CAT activity, while cerium nanomaterials with greater Ce3+ content enhance SOD activity. It was reported that Ce3+ has more oxygen vacancies providing more active sites for the binding of superoxide radicals on the surface [77][78][79]. By controlling the Ce3

Controllable physicochemical properties of WO_x thin films grown under glancing angle

• Rupam Mandal,
• Aparajita Mandal,
• Alapan Dutta,
• Rengasamy Sivakumar,
• Sanjeev Kumar Srivastava and
• Tapobrata Som

Beilstein J. Nanotechnol. 2024, 15, 350–359, doi:10.3762/bjnano.15.31

• revealed from the XRD studies, as-deposited NS-WOx films are amorphous in nature, whereas post-growth vacuum-annealed (at 673 K for 1 h) films show an amorphous-to-crystalline structural phase transition. XPS analysis confirms an increasing concentration of defect density in the form of oxygen vacancies

• conduction across the heterojunction with increasing film thickness indicates a possible role of oxygen vacancies in facilitating smooth charge transport till the thickness reaches 30 nm, above which the series resistance effect within the WOx film starts to dominate. Overall, this study demonstrates a wide

The microstrain-accompanied structural phase transition from h-MoO₃ to α-MoO₃ investigated by in situ X-ray diffraction

• Zeqian Zhang,
• Honglong Shi,
• Boxiang Zhuang,
• Minting Luo and
• Zhenfei Hu

Beilstein J. Nanotechnol. 2023, 14, 692–700, doi:10.3762/bjnano.14.55

• from +2 to +6 [1][2], leading to a range of molybdenum oxides. Molybdenum oxides include the fully stoichiometric MoO3 with a large bandgap above 2.7 eV, the reduced oxides MoO3−x with oxygen vacancies, and the semimetal MoO2. The degree of reduction influences the bandgap energy of molybdenum oxides

Titania nanoparticles for photocatalytic degradation of ethanol under simulated solar light

• Evghenii Goncearenco,
• Iuliana P. Morjan,
• Claudiu Teodor Fleaca,
• Florian Dumitrache,
• Elena Dutu,
• Monica Scarisoreanu,
• Valentin Serban Teodorescu,
• Alexandra Sandulescu,
• Crina Anastasescu and
• Ioan Balint

Beilstein J. Nanotechnol. 2023, 14, 616–630, doi:10.3762/bjnano.14.51

• indicate changes regarding the variation of the nanoparticle surfaces according to the value of the working pressure. Since XPS analysis is a surface measurement and the samples were calcined in air, the possibility to identify the presence of Ti3+ species and oxygen vacancies is small, but we do not

Plasmonic nanotechnology for photothermal applications – an evaluation

• A. R. Indhu,
• L. Keerthana and
• Gnanaprakash Dharmalingam

Beilstein J. Nanotechnol. 2023, 14, 380–419, doi:10.3762/bjnano.14.33

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

• Akeem Adeyemi Oladipo and
• Faisal Suleiman Mustafa

Beilstein J. Nanotechnol. 2023, 14, 291–321, doi:10.3762/bjnano.14.26

• ][104][110][144][145][146][147][148][149][150]. Doping reduces the bandgap energy, introduces intermediate energy levels to overcome constraints, creates trap sites to capture photogenerated charge carriers, and increases the absorption of visible light. Additionally, after doping, oxygen vacancies or

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• transforms into rutile. This could be due to the carbon components on the MWCNTs acting as a robust reducing agent for facilitating the transformation from anatase to rutile TiO2 by forming oxygen vacancies [30]. Generally, the capacitance of the photoelectrochemical electrode is associated with the

Recent trends in Bi-based nanomaterials: challenges, fabrication, enhancement techniques, and environmental applications

• Vishal Dutta,
• Ankush Chauhan,
• Ritesh Verma,
• C. Gopalkrishnan and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 1316–1336, doi:10.3762/bjnano.13.109

• type of halogen used. The activation of otherwise inert CO2 and H2O molecules is greatly aided by the ease with which photoinduced oxygen vacancies (OVs) are produced on the surface [25]. The excellent photocatalytic performance can be attributed to the layered crystal structures and small bandgap

• sample synthesized at pH 4 demonstrated outstanding visible-light photocatalytic performance regarding the degradation of RhB. This was due to the low thickness, exposed (001) facets, and an appropriate number of oxygen vacancies. This work proposed that revolutionary photoexcitation mechanisms were

• found on oxygen vacancies. Irradiation with visible light excites the electrons in the VB to transition into defect states. In addition, photogenerated defect states cannot readily recombine with photogenerated holes because oxygen vacancies operate as electron traps. Because of this, electrons trapped

Theoretical investigations of oxygen vacancy effects in nickel-doped zirconia from ab initio XANES spectroscopy at the oxygen K-edge

• Dick Hartmann Douma,
• Lodvert Tchibota Poaty,
• Alessio Lamperti,
• Stéphane Kenmoe,
• Abdulrafiu Tunde Raji,
• Alberto Debernardi and
• Bernard M’Passi-Mabiala

Beilstein J. Nanotechnol. 2022, 13, 975–985, doi:10.3762/bjnano.13.85

• is due to the structural disorder induced by the 2Ni dopants and the O vacancies. Furthermore, the analysis of the XANES signatures shows that the oxidation state of nickel atoms changes with the introduction of oxygen vacancies. Our study therefore shows a possibility to control the oxidation state

• large set of DMO. It is thus important to investigate other types of dopants in DMO or other types of oxide matrices doped with transition metals. Oxygen vacancies play a fundamental role in the aforementioned microscopic mechanisms since an excess or lack of oxygen vacancies with respect to their

• TM atom usually occupies the Zr site substitutionally. However, due to the difference in the oxidation state of the TM atom and Zr, oxygen vacancies are created to maintain an overall charge neutrality. This is aptly demonstrated in the experimental investigations of Fe-doped zirconia using X-ray

Hierarchical Bi₂WO₆/TiO₂-nanotube composites derived from natural cellulose for visible-light photocatalytic treatment of pollutants

• Zehao Lin,
• Zhan Yang and
• Jianguo Huang

Beilstein J. Nanotechnol. 2022, 13, 745–762, doi:10.3762/bjnano.13.66

• three weak peaks at 448, 479, and 490 nm, which are indexed to the recombination of photoinduced electron−hole pairs, freely excited electrons, surface defects, and oxygen vacancies on the band edges, respectively [36][61]. It is apparent that the PL intensities of the Bi2WO6/TiO2-NT nanocomposites at

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• a long time. It was assumed that zinc vacancies, oxygen vacancies, and other defects are candidates for recombination centres involved in the visible luminescence [78]. Studies concerning the green luminescence of ZnO in the past few years assumed that the oxygen vacancies are the most likely

• candidates for recombination centres involved in the visible luminescence of ZnO [77][79]. Thus, the electrical and luminescence characteristics of zinc oxide could be changed by the number of oxygen vacancies or other point defects (vacancies, atom substitutions, and interstitial atoms). Moreover

• also benefits the SERS enhancement. Doping zinc oxide–Ag nanoparticles with magnesium also introduces defect sites (surface defects and oxygen vacancies), which form new energy levels below the conduction band of zinc oxide, facilitating the charge transfer mechanism. In this case, besides the charge

Measurement of polarization effects in dual-phase ceria-based oxygen permeation membranes using Kelvin probe force microscopy

• Kerstin Neuhaus,
• Christina Schmidt,
• Liudmila Fischer,
• Wilhelm Albert Meulenberg,
• Ke Ran,
• Joachim Mayer and
• Stefan Baumann

Beilstein J. Nanotechnol. 2021, 12, 1380–1391, doi:10.3762/bjnano.12.102

• time dependence was shown to vary with dopant concentration (e.g., abundance of oxygen vacancies in ceria) and also depends on the ratio of grain boundary/grain bulk [22][23][24][25]. Single ceria grains in a mixed ion/electron-conductive composite have so far not been addressed by AFM-based

• in this study strongly depended on the surrounding. In single-phase ceria materials, oxygen is incorporated into oxygen vacancies in the structure at high temperatures [4][30]: Previous studies showed that at temperatures below 400 °C the concentration of defect associates in ceria increases because

• electrons are trapped at oxygen vacancy sites, allowing also for singly charged () or uncharged (VO) oxygen vacancies in close vicinity to Ce3+ ions [31][32], which show a strongly lowered mobility. For low temperatures, the common electroneutrality equation for acceptor-doped ceria can be shortened, as

The preparation temperature influences the physicochemical nature and activity of nanoceria

• Robert A. Yokel,
• Wendel Wohlleben,
• Johannes Georg Keller,
• Matthew L. Hancock,
• Jason M. Unrine,
• D. Allan Butterfield and
• Eric A. Grulke

Beilstein J. Nanotechnol. 2021, 12, 525–540, doi:10.3762/bjnano.12.43

• fewer oxygen vacancies and exhibits, therefore, a predominance of surface Ce+4, compared to a solvothermally synthesized nanoceria material with more oxygen vacancies, which produce a preponderance of surface Ce+3, it was hypothesized the NM-212 would have less catalytic activity. Another nanoscale

• +. Increased Ce3+ is accompanied by an increase in oxygen vacancies that weaken the crystal lattice [14]. According to the dissolution framework by Gray and co-workers, Ce3+ can follow more dissolution pathways (including oxidative dissolution) than Ce4+ [59]. The much greater percentage of Ce3+ on the surface

Interface interaction of transition metal phthalocyanines with strontium titanate (100)

• Reimer Karstens,
• Thomas Chassé and
• Heiko Peisert

Beilstein J. Nanotechnol. 2021, 12, 485–496, doi:10.3762/bjnano.12.39

• increased by introducing oxygen vacancies into the crystal structure or by doping (e.g., n-type doping with niobium, Nb5+). Generally, two different terminations of STO(100) are known, that is, the surface can be either TiO2- or SrO-terminated. The TiO2 termination can be achieved by (ex situ) acid

Exploring the fabrication and transfer mechanism of metallic nanostructures on carbon nanomembranes via focused electron beam induced processing

• Christian Preischl,
• Linh Hoang Le,
• Elif Bilgilisoy,
• Armin Gölzhäuser and
• Hubertus Marbach

Beilstein J. Nanotechnol. 2021, 12, 319–329, doi:10.3762/bjnano.12.26

• ) [13], thin layers of porphyrin molecules [14][15], and surface-anchored metal-organic frameworks (SURMOFs) [16][17]. For oxide surfaces it is known that the activation mechanism is based on reactive oxygen vacancies, which are locally created by electron-stimulated oxygen desorption [18][19]. Whereas

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• point defects. PL yields defect-related emission from all possible defects whereas EPR reveals only signals from paramagnetic defects [7]. Therefore, using EPR one obtains signals from the vacancies or interstitials that are ionized and become paramagnetic. In ZnO, singly ionized oxygen vacancies are

• ionized oxygen vacancies located either in volume or at the surface of the material. (b) PL spectra showing all possible defect centers, including non-paramagnetic ones. The defects emit visible light yielding a broad emission band [4]. (c) Tauc plot obtained from UV–vis reflectance measurements

Unravelling the interfacial interaction in mesoporous SiO₂@nickel phyllosilicate/TiO₂ core–shell nanostructures for photocatalytic activity

• Bridget K. Mutuma,
• Xiluva Mathebula,
• Isaac Nongwe,
• Bonakele P. Mtolo,
• Boitumelo J. Matsoso,
• Rudolph Erasmus,
• Zikhona Tetana and
• Neil J. Coville

Beilstein J. Nanotechnol. 2020, 11, 1834–1846, doi:10.3762/bjnano.11.165

• that facilitates easy adsorption of organic molecules and their transfer onto the active sites of TiO2 [22][23]. Additionally, the interaction between SiO2 and TiO2 could result in the creation of oxygen vacancies that promote charge-transfer processes and, hence, enhance the photocatalytic activity

• electronegativity and ionic radius between the metal ions and titania can alter the concentration of oxygen vacancies in the TiO2 lattice. Hence, the higher electronegativity of Ni2+ in NiPS [43] can induce defect sites within the structure and, consequently, alter light absorption and charge-transfer processes [51

• ][67]. These oxygen vacancies easily act as hole traps that lower the charge-carrier recombination rate, resulting in more free electrons that can give rise to more superoxide radicals upon reaction with adsorbed surface oxygen [23]. Furthermore, the flake-like NiPS morphology could act as a suitable

Nanocasting synthesis of BiFeO₃ nanoparticles with enhanced visible-light photocatalytic activity

• Thomas Cadenbach,
• Maria J. Benitez,
• A. Lucia Morales,
• Cesar Costa Vera,
• Luis Lascano,
• Francisco Quiroz,
• Alexis Debut and
• Karla Vizuete

Beilstein J. Nanotechnol. 2020, 11, 1822–1833, doi:10.3762/bjnano.11.164

• to point out that a comparison of bandgap values with different BiFeO3 samples is very difficult as particle shape, size, phase purity, as well as oxygen vacancies have a strong impact on the electronic structure of the resulting material. Photocatalytic activity The photocatalytic activity of all

Structural and electronic properties of SnO₂ doped with non-metal elements

• Jianyuan Yu,
• Yingeng Wang,
• Yan Huang,
• Xiuwen Wang,
• Jing Guo,
• Jingkai Yang and
• Hongli Zhao

Beilstein J. Nanotechnol. 2020, 11, 1321–1328, doi:10.3762/bjnano.11.116

• oxygen vacancies, and thus, increase the charge density of the Sn sites. The replacement of O with N can simultaneously decrease the release of CO2. While there are reports on experiments regarding the doping of SnO2 with non-metal elements, the mechanism of the effect of non-metal element doping on the

Adsorption behavior of tin phthalocyanine onto the (110) face of rutile TiO₂

• Lukasz Bodek,
• Mads Engelund,
• Aleksandra Cebrat and
• Bartosz Such

Beilstein J. Nanotechnol. 2020, 11, 821–828, doi:10.3762/bjnano.11.67

• molecule towards the surface. Also, the electrostatic landscape of a reduced rutile (110) surface prepared in UHV by sputter–anneal cycles is complicated. The cleaning procedure creates oxygen vacancies, which in turn leads to the formation of polarons near the surface [29][30][31]. Additionally, water

• molecules may dissociate at oxygen vacancies and form hydroxy groups on the surface. Both species can be recognized in our STM images and they both lead to the formation of dipole moments pointing away from the surface [32]. Their local arrangement may play a significant role in the interaction between a

Effect of Ag loading position on the photocatalytic performance of TiO₂ nanocolumn arrays

• Jinghan Xu,
• Yanqi Liu and
• Yan Zhao

Beilstein J. Nanotechnol. 2020, 11, 717–728, doi:10.3762/bjnano.11.59

• the catalyst, so the catalyst needs to have a certain adsorption capacity for dye molecules. Due to the presence of oxygen vacancies, the surface of TiO2 is usually negatively charged and has a good adsorption capacity for cationic dye molecules [36]. Commonly used cationic dyes are rhodamine, methyl

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• decoration of MWCNTs Prior to their deposition on the interdigitated electrode surface, the MWCNTs were treated by oxygen plasma to create oxygen vacancies on the walls of the CNTs in order to enhance their surface reactivity [14][15]. The detailed description of the experimental steps undertaken is

Improved adsorption and degradation performance by S-doping of (001)-TiO₂

• Xiao-Yu Sun,
• Xian Zhang,
• Xiao Sun,
• Ni-Xian Qian,
• Min Wang and
• Yong-Qing Ma

Beilstein J. Nanotechnol. 2019, 10, 2116–2127, doi:10.3762/bjnano.10.206

• % to 68.5% due to the synergistic effects of the oxygen vacancies, increased number of surface chemical adsorption centers as a result of SO42− adsorption on the TiO2 surface and the larger pore size. (3) S-doping increases the MB degradation rate from 6.9 × 10−2 min−1 to 18.2 × 10−2 min−1 due to an

• , the XP spectrum of O 1s can be fitted by three peaks and the CSs correspond to TiO2, –OH and oxygen vacancies (Ov) [44]. As the RS/Ti increases, the ratio of Ov increases from 4.3% (2-S0) to 22.9% (2-S3) and then decreases again to 19.9% (2-S5) (Table 3). The XPS signals of the oxygen vacancies were

• the O 2p orbitals. At the same time, the ratio of the Ov increases in the order of 2-S0.5 < 2-S1 < 2-S5 < 2-S3, as given in Table 3; therefore, the decrease of the DOS mainly results from an increase of the ratio of oxygen vacancies. Figure 6 shows the UV–vis DRS of 2-S0, 2-S0.5, 2-S1, 2-S3 and 2-S5

Improvement of the thermoelectric properties of a MoO₃ monolayer through oxygen vacancies

• Wenwen Zheng,
• Wei Cao,
• Ziyu Wang,
• Huixiong Deng,
• Jing Shi and
• Rui Xiong

Beilstein J. Nanotechnol. 2019, 10, 2031–2038, doi:10.3762/bjnano.10.199

• , China 10.3762/bjnano.10.199 Abstract We have investigated the thermoelectric properties of a pristine MoO3 monolayer and its defective structures with different oxygen vacancies using first-principles methods combined with Boltzmann transport theory. Our results show that the thermoelectric properties

• oxygen vacancies leads to a sharp peak near the Fermi level in the density of states. This proves to be an effective way to enhance the ZT values of the MoO3 monolayer. The increased ZT values can reach 0.84 (x-axis) and 0.12 (y-axis) at 300 K. Keywords: Boltzmann transport theory; first-principles

• calculations; molybdenum trioxides; MoO3 monolayer; oxygen vacancies; thermoelectric properties; Introduction Thermoelectric materials that can directly convert temperature gradients to voltage gradients and vice versa provide a valid strategy to mitigate the global energy crisis. Owing to the unique ability